M130a official driver download
Select the actual OS and required printing/scanning component.
USB-only M130a: do not apply nw/fn/fw menus
The exact model table, pp.1–2 identifies M130a G3Q57A with USB 2.0, an icon/LED control panel and manual duplex printing. It has no Ethernet, wireless, Wi-Fi Direct, document feeder or hardware fax. It prints in black; a shared download page’s wireless videos, fax/app wording or ePrint category do not add those features. Use the flatbed and the actual LED/numeric display, not another model’s touchscreen Setup menu.
Current Windows software: 2026-10-11
With Windows 10 (64-bit), then Windows 11 selected and the list refreshed, HP lists M130a/132a and Ultra M134a Full Feature Software and Drivers 44.11.2775, 193.8MB, 2022-05-18; Basic Driver 44.11.2775, 66.1MB, 2022-05-18; and Easy Start 17.6.14, 26.5MB, 2026-09-25. Easy Start requires Internet for installation. Choose the stated functions; “Basic” alone does not prove the scan tools you need are installed.
Follow the selected installer’s USB prompts and review its current requirements. The listing is not an installation test or a Windows ARM guarantee. The product’s older macOS/Linux compatibility labels do not establish every current OS version or architecture. The Windows10 list also showed separate firmware and network ePrint items; do not treat them as a USB print/scan fix or a network capability.
M130a not printing: compare the printer and PC
Configuration and supplies report without a PC job
With the printer on, paper loaded and covers closed, hold Start Copy until Ready starts blinking, then release. The configuration page prints; the supplies-status page prints with it. This is the Start Copy key, not Cancel, and no guessed hold duration is needed. Configuration test, printed p.143 · Supplies report, printed p.158
If the report fails, read the LED/display code and check paper, covers and supplies first. If it is normal but PC printing fails, compare USB, the queue and M130a driver. A good report alone does not prove a driver fault. A flatbed copy is a separate way to compare scanner/original problems with PC scan setup.
Ready, Attention, Supplies and Go/Er
Ready is steady when ready and blinks during receiving/cancelling jobs. Attention calls for checking the display; Supplies differs from it. The LED panel alternates Go with a two-digit status when confirmation is needed, or Er with an error code. These are actual manual codes, not counts of flashes. The table selects 13 useful groups; it is not every firmware/service code. Exact M130a LED panel, printed p.4 · Code table, printed pp.127–129
| Display / symptom | Check or action | Guide |
|---|---|---|
| Go/01 · Attention blinking | Manual feed: load the specified paper type/size, then Start Copy. | Paper / feed |
| Go/02 · Attention blinking | Manual duplex: reload for the second sides, then Start Copy. | Manual duplex |
| Go/03 or Er/25 | Job/settings or size mismatch: compare paper and job; Start Copy can accept loaded stock. | Size check |
| Er/01 or Er/02 | Input tray empty / cover open: load paper / close the top cover fully. | Paper / cover |
| Er/03 | Paper pickup failed; inspect stock and guides, then use Start Copy as directed. | Pickup |
| Er/04 · Er/05 · Er/06 | Jam in input tray / toner area / output area; use the matching path. | Jam locations |
| Er/07 · Attention and Supplies blinking | Toner or imaging drum missing or incorrectly installed. | Separate supplies |
| Er/08 · Er/09 · Er/10 | Toner / drum / multiple supplies very low; compare the configured stop/continue behaviour. | Very Low settings |
| Er/11 · Er/12 · Er/13 | Toner / drum / multiple supplies incompatible; check exact part and installation. | Compatibility |
| Er/20 | Cartridge sensor error; the manual directs toner replacement, not a driver repair. | Sensor and support |
| Er/26 | General engine error: Start Copy; if repeated, power off, wait 30 seconds, then restart. | Engine error |
| Er/30, /49, /50 or /79 · Attention and Ready on | Selected fatal-error codes: off/disconnect, wait 30 seconds, restart and allow initialization; service if persistent. | Persistent fault |
| Er/90 · Er/91 · Er/92 | Engine / scanner / control-panel cable error: Start Copy; HP support if persistent. Do not dismantle. | Service |
Eight practical cause checks
| Display / symptom | Check or action | Guide |
|---|---|---|
| USB printer is not detected | Common PC checks: powered device, known-good data cable, direct USB port and the exact M130a queue. | USB |
| Paper / open cover / Go confirmation | Read the actual Go/Er code and match paper, size and manual-feed/duplex prompt. | Paper / code |
| Er/04–06 paper jam | Distinguish input, toner and output paths; follow the appropriate illustration. | Jam |
| Toner / drum warning | Toner and imaging drum are separate parts; compare installation, part and Very Low setting. | Supplies |
| Report works, PC print fails | Common PC checks: queue/port, pause/failed job and exact model/OS component; a missing or wrong driver uses this route. | M130a driver |
| Faint / specks / streaks | Compare configuration output; inspect supplies and the model’s cleaning-page procedure. | Quality |
| Print works, computer scan fails | Check selected HP scanner, HP Scan software and USB; flatbed copy does not prove PC scan setup. | Scanning |
| Copy edges cut off / duplex not automatic | Use Reduce/Enlarge and manual-duplex prompts; this model has no automatic duplexer or ADF. | Layout |
Local USB queue and software
Common PC checks: connect a sound USB data cable directly, select M130a rather than an old/network queue, inspect pause/offline state and the first failed job, then try a known-good document. Reinstall only after comparing a device report and connection. No printer IP or WPS setup is needed for this USB-only model.
Paper size, feed and second sides
Match paper size/type with the application and actual stock; align guides without bending it. Go/01 and Go/02 request different actions. For duplex, follow the job’s reload orientation before Start Copy rather than treating the pause as a driver fault. A code accepting currently loaded paper does not guarantee the intended layout.
Three jam paths; toner and drum are separate
Follow the input/toner path illustrations, printed pp.144–149 or output procedure, printed pp.149–151. Lift the scanner assembly/open the top cover as shown, remove toner and then the imaging drum where required, clear paper with both hands without tearing, then reinstall drum and toner and close/lower both covers. The combined removal note in the manual belongs to M133/M134; do not apply it to M130a. Avoid touching the drum surface.
Very Low is not a single universal stop rule
The code table recommends replacement for Er/08–10, while printed pp.133–134 explain configurable Continue, Stop or Prompt behaviour; printed p.158 says acceptable print quality can permit continued use. Read the actual configuration and output quality. The compulsory HP33A/34A exception is for the other supplies, not the M130a’s listed HP17A toner/HP19A drum. Verify regional part compatibility before ordering; do not clear counters or bypass chip checks. Very Low options · Supplies quality guidance · Exact model supplies
Cleaning page through the USB software
For toner specks or recurring marks, the LED-panel route is HP Printer Assistant → Print → HP Device Toolbox → System → Service → Cleaning Mode → Start. Follow the software prompts and allow completion; this is not ink-head cleaning. The manual says USB Device Toolbox requires a full software installation and available features vary. Do not replace it with an invented touchscreen menu or browser IP. USB Toolbox condition, printed p.104 · Cleaning, printed p.159
HP Scan and the flatbed
The documented Windows route is HP Printer Assistant → Scan → Scan a Document or Photo. Confirm the selected scanner and USB connection, adjust settings, then scan. Missing scan components return to M130a driver; a working print driver alone does not prove scanning is installed. Compare a local flatbed copy and keep the glass/backing clean when both copies/scans have marks. HP Scan, printed p.68
Copy crop and manual duplex
The manual describes a 4 mm unprintable border. For smaller originals, move them away from the indicated glass corner; for a same-size original use Reduce/Enlarge to avoid cropping. Check app margins and paper size as common print-job settings. M130a’s second sides require manual reloading. Copy edges, printed p.166
Persistent engine or cable faults
Record the whole code and light combination. Use the restart/Start Copy steps only for the listed condition; persistent fatal or cable errors need HP support. Repeated driver installs cannot repair an internal engine/scanner cable. Firmware/signature codes are outside this selected table; do not accept unknown updates or reset the printer to hide an error. Factory reset is not the report operation and deletes saved settings/pages. Fatal faults, printed p.129 · Reset effects, printed p.131
Evidence checked 2026-10-11: exact M130a manual listing maps c05208327, Edition2 January2019,200pages, and c05211349 model specifications. PDF positions are12 higher than printed pages. Current selected download rows are separate evidence; no installer or firmware downloaded/run.