CJV200-130 official driver downloads
Open official Driver / Utility listingBefore installation, check the Windows 11 security caveat below and match the actual model, OS and RIP setup.
Drivers, RIP, profiles and the Windows 11 caveat
| Item | Check and action |
|---|---|
| Mimaki Driver | Official 64-bit 5.13.0, 16 October 2026, 129.79MB; lists Windows 10 (64bit), Windows 11 and CJV200-130. |
| RIP / RasterLink | Separate software prepares and sends print data. Check the installed RIP’s license, model and connection support. |
| Color profile | Match the actual media and ink set. Profiles and firmware serve different roles from the device driver. |
Official 5.13.0 details and prerequisites
The listed file is MimakiDriver-v5.13.0-64bit.exe. The listing does not establish ARM64 runtime, current macOS/Linux support or installation success.
Mimaki’s prerequisite for this version asks for Memory integrity to be turned off. This affects Windows kernel protection. Confirm compatible-driver options and security policy with Mimaki or the PC administrator before installation; do not treat disabling it as a routine printing fix.
Manual pp.38–40 separate driver, RIP/license, profiles and printer registration. Its registration example uses CJV200-160; choose the actual CJV200-130, fitted ink set and output port rather than copying the example.
Official cartridge-model manual p.39
Confirm the cartridge-model CJV200-130
This is an eco-solvent inkjet print-and-cut model. Official maximum print width is 1,360mm and maximum media width is 1,370mm. The manual cover names CJV200-75/130/160. This guide addresses the cartridge model; JV print-only and CJV200-160B bottle-model configurations need their own instructions. Match ink and supply options to the installed unit.
Official cartridge-model manual p.188
Check 1000Mbps LAN and USB transfer limits
| Item | Check and action |
|---|---|
| Ethernet | Use Cat6/6A and a 1000BASE-T PC/switch. The manual requires the same LAN and excludes a connection through a router. Check Local guidance → LAN Status for 1000Mbps; 100Mbps, 10Mbps or No Connect cannot print. |
| USB 2.0 | Use a RIP that supports USB. Slow transfer can pause the carriage at either end; do not assume a driver fault. Keep the cable connected during transfer. |
A steady green LAN-connector light indicates 1000BASE-T; orange alone is not evidence of 1000Mbps. Safely remove storage from the USB-connected PC: the manual identifies unsafe removal as a possible cause of 201 Command Error.
Official cartridge-model manual p.36
Official cartridge-model manual p.37
Run the nozzle test from LOCAL
First check head-height setup and loaded media. Follow the manual’s explicit requirement of at least 500mm wide media. Its separate warning that stock below 300mm cannot show the whole pattern does not establish a 300mm recommendation.
- In LOCAL, select TEST PRINT/CLEANING → Test Print and press ENTER.
- Choose Scan Dir. or Feed Dir. and press ENTER to print.
- Compare the pattern for missing or deflected lines.
Official cartridge-model manual p.73
Choose cleaning from the test result
| Item | Check and action |
|---|---|
| Soft | For deflected/bent lines. |
| Normal | For missing lines/nozzle clogging. |
| Hard | For ejection failures unresolved by Soft and Normal. |
Select the method under LOCAL → TEST PRINT/CLEANING → Cleaning, then check a fresh test pattern. If defects persist, follow the manual’s maintenance references or contact service.
Check ink status: p.75 gives a general block on cleaning at Ink Near End/Ink End, while p.177 allows a UISS-specific Ink End exception. Match the installed ink supply and device message; do not bypass an ink error.
Official cartridge-model manual p.75
Official cartridge-model manual p.177
CJV200-130 cause checks when printing fails
| Item | Check and action |
|---|---|
| Device message | For a red status lamp, read the display and matching message. |
| LAN speed | Check 1000Mbps and the actual cable/switch. |
| USB/RIP port | Check RIP USB support and the selected output port. |
| Driver | For 20A or a host driver-version issue, compare this model’s driver and the OS/security prerequisites. |
| Media and covers | Check loaded media, covers and clamp state. |
| Quality / profile | Compare the device nozzle pattern separately from RIP media/ink profiles. |
Host-setting comparisons are common diagnostics. Check active maintenance and pending jobs before taking action.
Seven selected warning/error messages
| Item | Check and action |
|---|---|
| COVER OPEN | Close the cover; open covers prevent printing/automatic maintenance. |
| Data Remain | RIP data remains. Review the job before choosing the documented REMOTE print or clear-and-cancel path. |
| Temporary Suspension | Printing is paused; review the job before resuming or cancelling. |
| 201 Command Error | Non-RIP or faulty received data. Review/clear the affected job, resend and check compatible cables/connections. |
| 202 Parameter Error | Received RIP data problem; use the same data/connection checks as 201. |
| 206 Print Mode Error | RIP parameters prevent printing; correct the output parameters/profile. |
| 20A Driver Version | Mimaki driver is too old. Review this model’s current driver route and its Windows 11 caveat. |
Contact the dealer/service office if errors persist or return. Any further power action for 201/202 must follow the full shutdown procedure on manual p.34; this guide does not prescribe a forced power cut.
Official cartridge-model manual p.175
Official cartridge-model manual p.179
Official sources and verification scope
Checked 27 October 2026. The cartridge-model manual is listed as version 2.3, document D203836-23, with 200 PDF pages matching printed pagination. It is distinct from the bottle-model manual. Current driver listings/details were checked; installer payload, signature, installation, firmware and physical printing were not tested.