Download DS620A driver
US manufacturer list with DS620A selected. Choose the OS package and check its notes.
- Match the full model number on the device label, including suffixes.
- Check your operating-system version and architecture on the official support page.
- Cancel pending print jobs before replacing an existing driver.
- Follow the manufacturer’s instructions for power, USB, and network connections.
DS620A model and connection
Official model sources checked: 2026-10-11
The US DS620A product page identifies a six-inch dye-sublimation thermal-transfer photo printer with USB 2.0. It is not a scanner/copier or a printer with native Ethernet/Wi-Fi. Match the full label and region; a separate print server is a different configuration.
Choose the correct Windows package
The selected DS620A download list, checked 2026-10-11, separates Windows 11 ONLY v2.0.1.2 (64-bit) from Windows 7/8/10 v2.0.1.1 (32/64-bit). Do not install the Windows 11 file on an older OS. The separate Mac driver and its included notes were checked on 2026-10-15; see the documented OS and USB conditions below. Mac firmware remains a different download.
Windows 11: install the package, then connect USB
- Confirm DS620A and the OS/architecture, cancel pending jobs and retain needed settings. Extract the official Windows 11 ZIP with USB disconnected.
- Follow its included manual to remove the previous DNP driver package first, especially after upgrading from Windows 10.
- Run DriverInstall.CMD from the official extracted package. Confirm the expected DNP installer prompts, then finish its driver-package wizard.
- Connect USB and turn on the printer. Confirm DP-DS620 under Settings → Bluetooth & devices → Printers & scanners, then restart the PC.
- Choose a Paper Size that matches the installed media and send a small test photo. This computer test also uses USB and the driver.
These steps come from the Windows 11 package's manual, section 1. For Windows 7/8/10 choose the separate package and its installation guide. Printing drivers, firmware and optional utilities are separate downloads; files are not redistributed here.
Driver Paper Size when PAPER/RIBBON alternate
The Windows 11 ZIP's driver manual (printed p.13, PDF p.16) uses printing preferences → Layout → Advanced… → Paper Size. Available sizes depend on loaded media; an offline device is assumed to have 6×4 media. Bring it online, check the actual roll/ribbon and choose a matching job size. Correct the setting before replacing the driver. Do not assume that every listed size or panorama mode works with every media/firmware/software combination.
Pair two 6×4 photos on 6×8 media
DNP’s Windows 11 driver manual v2.0.1.2 lists the DS620A as DP-DS620 (A). When you send a single 6×4-inch photo on 6×8-inch media, this model does not rewind the ribbon to save the unused half for the next job.
To pair two 6×4 photos in one 6×8 panel, check that the loaded media is 6×8. Set the driver’s Paper Size to 6×4. Select both images in the app and send them in one print job. The driver’s Multiple Layout pairs the photos, and the printer cuts the paper after it comes out. Sending one photo at a time in two jobs does not pair them.
During a 6×14 or 6×20 panorama, the paper moves out and back as the printer prints each section. That movement is part of printing the panorama.
See printed pages 16–18 (PDF pages 19–21) of the manual in the DS620A Windows 11 driver package for the layout table and example.
Windows 11: an Unspecified DP-DS620 device
First install the official package if it is missing. If the device is still Unspecified, section 1.4 of the included manual removes only the identified Dai Nippon Printing DP-DS620 device, disconnects USB, restarts the PC, then reconnects USB and turns on the printer. Confirm the DP-DS620 queue and restart after installation. Do not delete unrelated devices.
Media loading and recovery
Use the model's user guide for matching paper/ribbon, direction, slack and mechanism closure. Keep hands away from the cutter and hot head. The LED table below distinguishes depleted supplies, loading faults, size mismatch and cooling; changing the driver is not a general remedy for all of them.
When the 6 × 14 or 6 × 20 panorama size is missing
The DS620A uses standard DNP 6 × 8 inch media for 6 × 14 and 6 × 20 inch panoramas. DNP lists printer firmware 1.52 or later and either WCM-Plus or Hot Folder Print (HFP) 2.2 or later.
If the sizes are missing, check the loaded media, the printer firmware version and the sizes available in the app sending the job. For regular photo jobs, see the paper-size check.
During a panorama, the paper moves out and back several times before the final cut. Keep the exit clear and wait for the cut before taking the print. DNP excludes the standard and enlargement trays for this mode.
If paper stops and an error light stays on, see the indicator checks for the recovery steps. If standard photos also fail to send from the PC, see the DS620A driver guide.
DNP product specifications · Official Hot Folder Print guide · DS620A hardware manual
Panorama requirements checked November 4, 2026.
See ribbon use and pairing for 6×4 jobs on the same media.
Mac driver download: package notes and supported scope
Checked 2026-10-15: the US DS620A Mac list separates the print driver from firmware. Its ZIP contains README FIRST and an English v5.2 user guide. The README identifies v5.2.7 build 669, release 2023-08, intended for OS 13/12/11. This dated scope does not verify newer macOS or Intel/Apple Silicon/Rosetta operation.
Open DS620A Mac driver downloads
Official ZIP: README pp.1–3 and English guide printed pp.5,12–13
The user guide’s printed p.5 pairs “10.13” with Ventura and “10.12” with Monterey; it supplies no actual CPU list. These labels differ from the README. Use the README’s explicit 13/12/11 scope and request current regional confirmation for an unlisted system.
Mac USB installation: let the printer add itself
- Check DS620A media and Ready status; disconnect USB from the Mac. Retain existing settings before replacing software.
- Download the Mac print-driver ZIP, review its README and licence, then use the driver PKG and follow the installer. The firmware DMG is a different file.
- After installation, power the printer and connect USB. The README expects automatic addition in about one minute; avoid creating a duplicate queue with + during normal setup.
- Choose a Paper Size matching the installed roll/ribbon before testing. Letter is the Mac default and can prevent this photo printer from printing.
Mac printing errors: size, queues and iSerial
- If the queue exists but printing fails, check Paper Size and USB before reinstalling. The guide’s printed p.12 allows manual + only as recovery when automatic addition still fails after its queue/power checks.
- Full-release/multiple-printer operation is conditional on iSerial capability and enablement. The README limits a non-iSerial setup to one DNP printer; older DS620A units can have a different firmware/capability state.
- The supplied uninstaller removes all DNP printers and driver files for every Mac user. It is broader than removing one queue in Printers & Scanners; compare the README’s old-version/fault conditions before using it.
DS620A not printing: read the LEDs before changing the driver
If you just replaced the roll, check whether the printer is initializing the paper.
The front LEDs identify device states. Compare which indicators are steady, flashing or off; a red ERROR light alone is not enough to identify the cause. The shared model manual, pages 21–22, supplies the following nine states applicable to DS620A. POWER is steady green in the first eight rows; cooling is the exception. PAPER/RIBBON are orange and ERROR is red. These are LED states, not numeric fault codes.
Nine LED states: paper, ribbon, mechanism and cooling
| LED pattern | Meaning | First action and source |
|---|---|---|
| PAPER flashing; RIBBON/ERROR off | Paper roll empty | Load a new matching paper roll. Media loading, p.14 |
| RIBBON flashing; PAPER/ERROR off | Ribbon depleted | Load a new matching ribbon. Media loading, p.14 |
| PAPER and ERROR flashing; RIBBON off | Mechanism open, paper not loaded | Load the paper correctly, then close the mechanism. Loading sequence, p.14 |
| ERROR flashing; PAPER/RIBBON off | Mechanism open | Close the mechanism unit. Closing sequence, p.18 |
| PAPER and ERROR steady; RIBBON off | Paper loading fault | Check the paper seating and path. If jammed, use the illustrated removal procedure. Paper jam, pp.22–23 |
| RIBBON and ERROR steady; PAPER off | Ribbon loading fault | Check ribbon seating and direction; use the model procedure if it is caught. Caught ribbon, p.24 |
| RIBBON/PAPER flash alternately; ERROR off | Requested size differs from loaded media | Match application/driver Paper Size to the actual paper and ribbon before reinstalling. DS620A driver and size settings |
| ERROR steady; PAPER/RIBBON off | System fault | Reset the ON/Standby switch as instructed after printing has stopped. If it persists, contact the dealer. System-fault guidance, p.21 |
| POWER flashing; other LEDs off | Print-head cooling | Wait for automatic recovery. Cooling indication, p.22 |
The manual's missing scrap-box indication is explicitly for DP-DS820 only and is excluded here. Still fit the DS620A scrap box for safe printing (p.18). For a stopped partial cut or a power interruption, use p.25; do not force the cutter or mechanism open. Do not switch to Standby during an active print. For jam removal, wear suitable lint-free protective gloves and contact support if strong force would be needed (p.23).
Five blank sheets after changing the paper roll
When you close the mechanism after loading paper with the DS620A on, the printer cuts away the outer paper and ejects five blank sheets. This clears the part of the roll that may be dirty. The manual says this initialization does not run if you load the roll before moving the ON/Standby switch to ON. In that case, the absence of blank sheets does not by itself indicate a fault.
- Empty the scrap box at each roll change. After printing has finished, release the opening lever and slide the mechanism out. Lift the paper lever and open the front cover. Lift the scrap box straight up by its center. Pulling it out at an angle can damage it, and the cutter above it can injure your fingers.
- Listen for the loading beep. Fit the new roll to the holders without gaps. Turn the roll as shown in the manual until the printer accepts the leading edge. The buzzer sounds and the flashing orange LED goes out.
- Refit the scrap box before closing. Put the box back, then close the front cover and the mechanism. The manual lists a dedicated missing-box light pattern for the DS820 series only. Always fit the box on the DS620A too, to keep fingers away from moving parts.
If paper still stops or an indicator remains after initialization, check the LED pattern and paper-jam instructions. If the printer feeds normally but only PC jobs print blank or fail, check the app preview and use the DS620A driver guide to verify the queue and print settings.
Official sources checked 2026-11-09 · Loading confirmation · Paper initialization · Emptying the scrap box
Resume a Windows photo job after a paper or ribbon error
When the DS620A runs out of paper or ribbon, check Print Re-try before resending the photos. In Windows 11, open printing preferences for DP-DS620 and choose Layout → Advanced… → Print Re-try. Use the DS620A driver downloads to select the package for your Windows version.
- Enable. With the printer still powered on, it resumes using the print data it retained. If the new roll needs paper initialization, let it finish first. To avoid duplicate prints, check which photos come out before sending the job again.
- Disable. The printer clears its buffered print data when the error occurs. DNP recommends this setting for apps that handle error recovery themselves. Check whether the photo booth app resends the job automatically, then send only the missing photos if needed.
- Errors that require a power cycle. Turning the printer off clears its buffered data even with Enable selected. Follow the DS620A LED and recovery instructions, then resend the missing photos once the printer is ready.
See the Windows 11 package’s driver manual, printed pages 13 and 15 (PDF pages 16 and 18). The menu path shown is for Windows 11.
LEDs clear but the computer still cannot print
Keep the standard USB connection distinct from a separate print server. Select the DP-DS620 queue and compare the application's printer and media choice. Queue pause and a failed first job are common PC checks, not a DS620A device fault code.
| PC symptom | Check | Help |
|---|---|---|
| Windows 11 lists an Unspecified device | Verify the official package was installed before USB connection. | DS620A package and exact-device recovery |
| Device is ready; PC photo job fails | Check USB, selected DP-DS620 queue, pause state and exact OS package; recheck Paper Size. | DS620A driver guide · Common queue checks |
The automatic paper initialization after loading and closing the mechanism can eject five blank sheets (p.18). That is media preparation, not a standalone photo test. After the LEDs clear, send a small test image from the computer to check the USB/software path.
Paper jams: rewind, remove forward and trim damage
The DS620A guide separates paper jams, trapped ribbon, partial cuts and power lost during printing. Identify how the printer stopped and use the matching drawing.
Use lint-free protective gloves and watch for sharp paper or internal edges. Do not touch the cutter above the scrap box. Never switch to Standby during printing; the recovery below applies to an already stopped printer in the stated condition. If release requires force or fails, contact DNP service.
Partial cuts and power loss: when the mechanism is locked
| Case | Next check |
|---|---|
| Partial cut | Cycle ON/Standby to Standby, then ON, so the cutter can return to its waiting position. Contact service if it will not release. Remove the partly printed paper and follow the paper-jam procedure below. |
| Power loss | The mechanism cannot be pulled out in this state. Standby, then ON lets the printer cut and eject the partly printed paper as scraps before the mechanism can open. Check for remaining partly printed paper; use the jam procedure below if any remains. |
Six steps for a paper jam
- Release the opening lever and draw out the mechanism. Avoid force; if it is locked after a power interruption, first use the applicable recovery above.
- Remove the ribbon cassette from the printer.
- Turn the spool opposite the feed direction to rewind the paper, as in Fig. A on page 22. Then gently draw the paper forward, away from the printer, as in Fig. B. Use only light pressure.
- If it will not come out easily, cut the damaged edge and put the removed roll aside as in Fig. C on page 23. Gently remove remaining scraps forward as in Fig. D. Keep removed media on a clean protective bag or sheet.
- Trim away wrinkled or partly printed sections evenly with scissors. Leaving damage or an uneven edge can cause another jam or incorrect operation.
- Reload using the official paper/ribbon loading procedure beginning on page 14. Do not assume every jam is a driver fault or is solved by cutter recovery alone.
Page 22, Figs. A/B · Page 23, Figs. C/D and even trimming · Reload paper / ribbon
| Case | Next check |
|---|---|
| Paper jam | Check actual trapped paper, damage and removal direction. Removal steps → |
| Paper size | Match loaded media with the app/driver Paper Size. Paper size → |
| PC jobs only | Common host checks: compare USB, selected queue and the exact-model driver for the OS. Same-model driver → |
Verified 23 October 2026: User Guide 3.0.2 linked by the DS620A-filtered official list; selected pages 1, 14, 15, 22, 23 and 25 of 30 were visually reviewed. Earlier Windows, Mac, LED and quality evidence retains its dates. No physical jam clearing, printing, installation or firmware change was performed. Exact-model manual list
Trapped ribbon: wind past the join, then initialize paper
Use this path after printing has stopped. First follow page 22 to release the opening lever, open the mechanism and remove the cassette; page 24 then gives these seven steps. If a partial cut or power loss has locked the mechanism, use the matching recovery branch first and avoid force.
Use lint-free protective gloves and avoid sharp internal edges, the cutter above the scrap box and a hot print head. Keep removed media on a clean protective bag or sheet. Do not switch to Standby during printing.
- Draw out the trapped ribbon as shown in the first diagram on page 24.
- Cut the ribbon at the section shown in the diagram.
- Carefully remove ribbon left inside the printer and check for remaining pieces.
- Rejoin the ribbon with tape or similar material as illustrated on page 24.
- Turn the take-up roller until the taped joint is no longer visible. Distinguish it from the supply side and keep the ribbon free of slack.
- Reinsert the cassette. Compare page 18: the supply side faces the front.
- With ON/Standby set to ON, reload the paper. Closing the mechanism starts paper initialization and ejects material printed during the error. The guide says the error cannot clear until this initialization is performed.
Official page 24: seven ribbon steps and winding diagram · Opening and cassette removal, page 22 · Cassette direction and initialization, page 18
| Case | Matching check |
|---|---|
| Trapped ribbon | Compare the illustrated removal, join, winding and reload steps above. |
| Paper / locked unit | Use the separate paper removal and partial-cut/power-loss branches. |
| PC-only failure | Common host checks: compare USB, the DP-DS620 queue, actual Paper Size and this DS620A driver guide. |
Page 24 warns that ribbon pieces left inside can affect photo quality and refers to platen-roller cleaning. Follow the existing marks/roller guidance and unplugging and head-cooling precautions. Keep cleaning preparation separate from the powered reload in step 7.
Paper ejected during initialization is not a photo test or proof of driver installation. Check the LEDs after recovery. Contact DNP if pieces cannot be removed safely or jams recur. Do not invent a tape specification, turn count or consumable-counter reset.
Ribbon evidence checked 27 October 2026: the current DS620A-selected listing links User Guide 3.0.2. Eight whole pages (cover, 17, 18, 22–26) were reviewed, within a 30-page guide. Earlier Windows, Mac, LED, paper-jam and quality dates remain unchanged. No physical ribbon recovery, printing, settings change or current OS/CPU compatibility test was performed.
Transport: remove media and check the original packing
Unplug the printer before moving it. The manual says not to carry it alone or by its power/USB cable.
| Item | Before transport |
|---|---|
| Media | Remove the ink ribbon and paper roll; transport or store them separately. |
| Cables / tray | Remove USB cable, power cable and paper tray, and pack these separately. |
| Packing | Keep the original packing and head protection. Follow the diagram for the cassette, front cover and box orientation. |
After setup, compare LED states and USB checks. PC-only failures lead to the DS620A driver guide.
Checked 29 October 2026: v3.0.2, pp.8–9 and 28. Earlier software checks retain their dates. Official repacking diagram
Repeating marks and uneven photos: compare the symptom first
Quality guidance verified 19 October 2026: DS620/DS820 User Guide v3.0.2, pp.26–27. These two cleaning sections cover the DS620 family; DS820-only controls are not imported.
| Issue | Compare |
|---|---|
| Regular marks | About 50 mm spacing at the same position, or dirt on the white back: the manual points to contamination on the platen roller. p.26 |
| Uneven / gaps | Contamination on the thermal head can affect the image. This alone does not prove the head is damaged. p.27 |
| PC-only problem | Common comparison: an app-specific layout or queue failure needs paper-size/USB checks first. Exact DS620A driver guide |
Cleaning precautions: identify the illustrated part
Finish printing, unplug the printer and let the head cool before cleaning. Use lint-free protective gloves, avoid sharp edges and touch only the identified cleaning area. Do not use benzene or thinner.
| Part | Official guidance |
|---|---|
| Platen roller | Follow the media-opening/removal diagrams and turn the roller while wiping with soft gauze/cloth moistened with ethyl alcohol. pp.14–15 · p.26 |
| Head | Locate the thermal-head cleaning area visually and wipe gently with the same specified material; avoid bare-hand contact. For persistent defects, follow the exact named polishing-sheet guidance or ask service; do not substitute abrasives. p.27 |
Keep removed paper/holders on a clean protective surface. If the part or procedure is unclear, use model-specific service. No physical cleaning or test printing was performed for this guide. Media handling p.15